""" - Durable aerodynamic PP body and two-piece carbon frame construction Only 8 screws to separate the plastic main body from the carbon frame, motors and electronics Fast, easy and cheap repair or customization - Inverted pusher style design for greater thrust and efficiency Propeller thrust can move without any disturbance to the structure or cables; Increased flight time, less noise and less propwash! - Powerful XING 1404 motors to carry your GoPro bare Light, efficient and with maximum power for its size; More than enough boost for unrestricted cruising and aerobatic flight!- Weight less than 250g including 4S 650mAh battery and Hero8 bare Flight Time: Used Batteries: iFlight Fullsend 4S With GoPro Naked: 650mAh 3-5min, 850mAh 4-6min Without GoPro Naked: 650mAh 5-7min, 850mAh 6-8min Features: - SucceX-D 20A F4 Whoop AIO V3.2 h High performance to save weight and space - Polar Vista HD digital Caddx system DEFECT AND DEFECT: - First use of one of our BNF? We have carefully prepared an article in the BNF General Guide to make your registration as easy as possible! - Don't worry about tuning, we've already done it for you! Basic PID and filter tuning have been applied for a great flight experience! - Angle Mode (Auto Balance Level Mode) is enabled by default to ensure your first flight doesn't end up crashing! Changelog: August 2021: XING 1404 5500KV changed to XING 1404 4600KV ProTek25 pusher BNF specifications: - Electronics: SucceX-D Whoop AIO V3.2 (SKU: S010673) - Motor: XING 1404 4600KV (LINK) - Wheelbase: 108 mm - Body size: 76.3*76.3mm - Top plate thickness: 3mm - Top and bottom plate spacing: 21mm (aluminum spacer height) - Propeller size: 2 .5 inch - FC Model: 25.5*25.5mm/20*20mm - FPV Cam Spacing: 20mm - Weight: 143.8g (without battery) Components and Parts Included ProTek25 Pusher HD Quad BNF Quadcopter pre- built and tested - 1 iFlight ProTek25 clip-on frame - 1 Caddx Polar Vista Digital HD system kit - 1 Sigma ipex / UFL LHCP 5.8g iFlight antenna - 2 iFlight Nazgul 2525 propellers (4-pack - colors may vary) - 1 battery strip 15x150mm - 1 battery strip 15x180mm FC + ESC AIO // SucceX-D Whoop AIO V3.2 (SKU: S010673) * Size: 41*41mm * Model of mounting: 25.5*25.5mm / 3mm * Connector: Micro-USB * MCU STM32F411 * GyroMPU6000 * OSD: IFLIGHT OSD (AT7456E * Blackbox: 16MB Built-in Flash * BEC output: 5V 2.5A * Barometer: DPS310 * Constant Current 20A30A Explosion * 2-6S Input * Current Sensor, Yes * BLHeliBLHeli-S * ESC Telemetry, No * Target IFLIGHT_F411_AIO * ESC Firmware: GH-30 BLS Suggested Additional Parts DJI Goggles HD FPV Radio Control Battery 4S 850mAh (LINK) / 4S 650mAh (LINK) DJI remote control is recommended for beginners because you don't need to set up another receiver, but it is also optional on this BNF drone because it is not NOT necessary to use the FPV system. If you don't choose to use the DJI remote, you can choose a receiver option for your transmitter and then connect to your own radio as usual. Our Frsky receivers come with the latest ACCST 2.XX standard firmware. Be sure to use compatible transmitter firmware! If you are using multi-protocol receivers (Radiomaster, Jumper, etc.), select the 2X or X2 radio protocol. The battery holder is not included and must be purchased separately! """